Brad Clayton Posted December 14, 2007 Share Posted December 14, 2007 Tsb for 6.4l blowing fuse 74. New gasket kit 8C3Z-9G805-A, but you still have to check to make sure the wires are covered with some sort of protection. labor op 072602A, labor time 8.4 hrs. Quote Link to comment Share on other sites More sharing options...
LARRY BRUDZYNSKI Posted December 15, 2007 Share Posted December 15, 2007 Can you post the TSB so everyone can see it? Quote Link to comment Share on other sites More sharing options...
Brad Clayton Posted December 15, 2007 Author Share Posted December 15, 2007 Quote: TSB 07-26-2 6.4L - INTERMITTENT NO START / LACK OF POWER - DTC P0003 AND/OR BLOWN FUSE 74 - BUILT PRIOR - 8/20/2007 Publication Date: December 13, 2007 FORD: 2008 F-Super Duty ISSUE: Some 2008 F-Super Duty vehicles built prior to 8/20/2007 equipped with a 6.4L diesel engine may exhibit a lack of power or no start with possible DTC's P0003, P0004 and P0091 caused by circuit CBB12 at the high pressure pump gasket grounding to the high pressure pump body (may also result in fuse 74 being blown). ACTION: Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE Unplug connector C1926 near the high pressure fuel pump cover. Check pin 4 green/white and pin 2 yellow wires for a short to ground. If either one is shorted to ground, remove the high pressure fuel pump cover and replace the pump cover gasket/harness that contains the grounded wire ONLY. The high pressure fuel pump does not need to be removed and replaced. Refer to the Workshop Manual (WSM), Section 303-04C. When removing the low pressure fuel lines and high pressure fuel tubes from the high pressure pump, use a back up wrench on the high pressure pump fittings to make certain that the fittings are not loose as the cap nuts and high pressure fuel tubes are removed (this may cause a fuel leak). When installing the new high pressure pump cover gasket/harness, verify that the VCV wires are wrapped in either high temperature convolute or a mesh style abrasion wrap. When making electrical connections to the high pressure fuel pump, pull the connectors to verify connectors are locked in place. PART NUMBER PART NAME 8C3Z-9G805-A Kit-Cover Fuel Pump WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part. OPERATION DESCRIPTION TIME 072602A 2008 F-Super Duty 6.4L: Replace High Pressure Fuel Pump Cover Gasket, Includes Time To Remove And Install Cab, And Perform Diagnosis (Do Not Use With 6007B, 6007B47, 6007B50, 6007B5, 12650D) 8.4 Hrs. DEALER CODING BASIC PART NO. CONDITION CODE 9G805 X1 Quote Link to comment Share on other sites More sharing options...
Tony302600 Posted December 15, 2007 Share Posted December 15, 2007 to whoever has done this repair what do you guys think on the labor time? Quote Link to comment Share on other sites More sharing options...
Brad Clayton Posted December 15, 2007 Author Share Posted December 15, 2007 If you can get the cab off quickly, then the actual repair is a breeze. So beating the time shouldn't be a problem. Quote Link to comment Share on other sites More sharing options...
G. Bedford Posted December 16, 2007 Share Posted December 16, 2007 My concern is some techs have found the HPFP is damaged and the vehicle is a no start or fails soon after the wire repair. I just hate doing things twice when an "over repair" would be the better choice. Quote Link to comment Share on other sites More sharing options...
Tony302600 Posted December 17, 2007 Share Posted December 17, 2007 "you're damned if you do....you're damned if you don't" is my favorite way of describing the diesel tango. Like iwas told....siemens said that the pump is not affected when either wire is grounded. But who knows. Quote Link to comment Share on other sites More sharing options...
OHNO60 Posted December 18, 2007 Share Posted December 18, 2007 I DID ONE YESTERDAY. WELL GOTTA SAY THE 8.4 SUCKS.BUT NOT IMPOSSIBLE. JUST HAVE TO GET THE CAB OFF TIME AS LOW AS YOU CAN.HAD RED WIRE FOR VCV SHORTED.NEW GASKET HARNESS HAS INSULATION AROUND WIRES. Quote Link to comment Share on other sites More sharing options...
Jeff_ Posted December 18, 2007 Share Posted December 18, 2007 Quote: My concern is some techs have found the HPFP is damaged and the vehicle is a no start or fails soon after the wire repair. I just hate doing things twice when an "over repair" would be the better choice. AuthorTopic:6.4l code p0003 Print Topic CHAD LAWSON Ed Murdock Ford Lavonia, GA (706) 356-1933i have a 08 6.4l with a code p0003 (fuel volume regulator control circuit low) and won't go over 1800rpm. has anybody seen this. October 19, 2007 2:17:05 PM Charles DeGroot Greiner Ford Lincoln Mercury Casper, WY (307) 266-1680Short to groud under fuel pump cover?? October 19, 2007 2:58:43 PM ROBERT GAULT Crossroads Ford, Inc. Cary, NC (919) 467-1881Charles is correct. We had one. October 19, 2007 3:17:11 PM jasen paulsen Red Johnson Ford Inc Hammon, OK (580) 473-2241we had one too, do it with the cab on, not that bad October 19, 2007 6:14:39 PM Marc Vukicevich Holman Ford-Mount Laurel Mount Laurel, NJ (856) 866-0111Be sure to also replace the High Pressure Pump as hotline said shorted wire will damage the pump. We had 2 last week with same concern. Much easier with cab off. Not too bad. October 19, 2007 8:44:14 PM Charles DeGroot Greiner Ford Lincoln Mercury Casper, WY (307) 266-1680Both we had had to be cab off the turbo inlet pipe fasteners really suck the big one assuming you can actually get them loose without stripping or breaking them . Not to mention the aftershock of exhaust leaks because it's virtually impossible to follow the WSM procedure to torque the up piped EDOC and brackets in any kind of sequence with the cab on. October 20, 2007 10:22:58 AM ROBERT GAULT Crossroads Ford, Inc. Cary, NC (919) 467-1881All those fasteners and gaskets are a one time use. They all have to be replaced whenever the exhaust is removed from the back of the engine. October 22, 2007 8:15:10 AM TOM ROHR Hill Ford Lincoln Mercury, Inc Portage, WI (608) 742-7141Pull the cab and put HP pump cover gasket and the HP pump assembly . Otherwise like me youwill end up doing it twice . October 22, 2007 9:52:28 AM FRANK BARKER Dale Jarrett Ford Indian Trail, NC (704) 283-8521yEP cHARLES HAS GOT THAT ONE,i'VE HAD SEVERAL October 26, 2007 8:24:44 AM Quote Link to comment Share on other sites More sharing options...
Jeff_ Posted December 18, 2007 Share Posted December 18, 2007 See that part in there where Hotline KNOWS there's a good chance the pump is damaged when a short occours. Yet the TSB wants us to just replace the wiring first and reassemble the vehicle...That is because a pump costs more than 8 hours of our time, thus ford is more than willing to take that chance. I'm not so sure that I'm willing to take that chance though. /forums/images/%%GRAEMLIN_URL%%/scratchhead.gif Quote Link to comment Share on other sites More sharing options...
Keith Browning Posted December 18, 2007 Share Posted December 18, 2007 Ahhh, but Jeff, I have a bad taste in my mouth about HPFP advice. Earlier this year I had a truck that would lose power and surge wildly once warmed up. I had codes, performed the pinpoint tests and needed assistance with the tests because my PC stopped displaying the tests correctly. Long story short, The PCED instructed us to replace the PCM. Well, the engineer (I do have a lot of respect for these guys in general) said "but that wont fix it, we have seen a bunch of these... replace the fuel pump." New pump goes in, truck sits two weeks waiting for the new pump cover gasket to come off backorder, then hits the road. Comes back on a hook. Same concern. I run through the tests again and the PCED again instructs to replace the PCM. HotLine insists it a bad pump, "install another." /forums/images/%%GRAEMLIN_URL%%/scratchhead.gif A lot of discussion and debate takes place at my dealer and with our FSE who agreed that a new pump will not fix it. To "different" engineers call me from Ford saying it is worth a try and also agree to replace the PCM. PCM fixed the truck. Here's the icing on the cake; We are a dealer that has to use RTDA (Real Time Diagnostic Assistance) for prior approval on modules and such... despite being told to go ahead by two engineers, an FSE and some other manager, we somehow forgot to call the PCM in. They would not pay the claim. Ford Motor Company should be ashamed. As far as I am concerned, the ENTIRE repair was their screw up. My point? Use your best judgement but cover your ass, dot your "I's" and cross your "T's." Did I say long story short? Quote Link to comment Share on other sites More sharing options...
Tony302600 Posted December 18, 2007 Share Posted December 18, 2007 not to highjack but we got memo's on our toolboxes saying that we have to call in any module on the sheet also keith. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.