Steve Mutter

wear can I get a dye to put in the fuel system,I am looking for a leak on A 6.4 diesel

try looking on ebay,they seem to have alot of factory tools for sale all the time

do you mean this one 20123 2008 F-SUPER DUTY - 6.4L - P0401/P0402/P2002/P244A/P2453/P2455 AND/OR DPF DAMAGE CAUSED BY AFTERMARKET EQUIPMENT SOME 2008 6.4L DIESEL VEHICLES MAY SET DTC P0401,P0402,P2002,P244A, P2453, P2455 OR HAVE A DAMAGED DPF/DOC (BLACK SOOT IN TAIL PIPE, BLACK OR WHITE SMOKE) RESULTING FROM AFTERMARKET MODIFICATIONS. BEFORE PROCEEDING WITH NORMAL DIAGNOSTICS, INSPECT THE VEHICLE FOR NON-APPROVED AFTERMARKET AIR INDUCTION SYSTEMS, AND OR AFTER DOC/DPF EXHAUST SYSTEMS OR ELIMINATION OF THE DOC/DPF AND OR PERFORMANCE ENHANCING PROGRAMS. THE USE OF NON APPROVED AFTERMARKET AIR INDUCTION SYSTEMS CAN ALSO CONTAMINATE THE MAF SENSOR, AND CAUSE INACCURATE EGR OPERATION AND FALSE DIAGNOSTICS CODES. REPLACEMENT OF FACTORY COMPONENTS WILL NOT RESOLVE THESE CONCERNS, AND SHOULD NOT BE ATTEMPTED OR COVERED UNDER WARRANTY. PLEASE REFER TO THE WARRANTY AND POLICY MANUAL, SECTION 3, FOR WARRANTY IMPLICATIONS OF REPAIRS RELATED TO VEHICLE MODIFICATIONS. EFFECTIVE DATE: 02/05/2008

another tech did one in our shop on a taurus,it was just off warnenty,it was going to be a 12 hour job till they awa it,you summed it up shity idea to put it inside the timming cover

flate rate hear

Aaron,if you go to http://www.protechnician.com you can read all the new tsb's befor you can read them on are inford site, it's a/t time for diag

I have an 09 f-350 with 54 km Harley,turbo noisey and oil coming out the tail pipe,the turbo has failed but why? so I called hotline and they told me that they have see a couple of these "Steve, We have seen this concern a few times. The most common cause is the banjo bolt for the oil feed line did not have enough holes drilled into it. There should be four holes (a drill bit from one direction makes to holes and turn the bolt 90 degrees another two holes)" has anyone run into this befor? and are there other things that can block oil flow to the trubos?

un bolt the motor mounts and put a stand under the crank pulley, lift the engine up un bolt the pan and the oil pickup and it should come right out

does it have a vmac set up on it,I had one that did some funny things,it would turn it's self on and bypass all the fail safes and ramp up the rpm by itself,they took it to where they had the vmac installed and all that shop did was installed a new harness for the pedal? but that fixed it, I have seen non ford idle up kits do odd things too

well I could not do it and just as well the push rod was bent,I don't think there is any easy repair on this diesel, still on the 6.4 learning curve

cam followers like to go for sit downs,we have see a couple in are shop

can the rocker arms be changed without removing the fuel rail? getting my parts today just wounder if anyone has done this

any word when the recall will be back in action?

I had a truck that had a wire chafe on the left valve just after the big conector,it would run rough every now and then,it's worth a look

sounds like my shop,there are techs at my shop who try hard and do good work,they want to get the repeat business,but all it takes is the one that does not care for whatever reason, in the end it makes our job alot harder then it has be

we had one that had a glow plug problem,the customer bought a used 6.4 and then drove it to Alberta and then broke down there,I had one turck with water contamination and one the other day that got 4 jugs of washer fliud in the tank(there is something funny going on with this one), blue washer fliud looks funny when its mixed up with diesel fuel

I wounder if you can claim 07-23-24 for oil in coolant and then claim 08-23-1 to clean the system? I like how they have pictures

wow! I like it. can't wait till they put that 6.2 in the mustang

you should also look into getting Orthodics,back pain starts with your feet,also don't cheap out on your work boots,a good pair goes along way! hope this helps

roush has this update for the pcm for canadian supercharged truck's becuase of fuel quality,we sent the pcm for this update and now the truck runs like shit,they have told me there is nothing wrong with there update(at this time). they don't want me to replaced the plugs but they want me to set the gap to 30 thou. I have ordered a gapping tool from steeda but other people have told me that they just bend them back,so far I have done nothing becuse roush does not want to pay(and I don't think the cust should pay) and the sm is more worried about who is going to pay the rental car for the cust, I feel sorry for the cust and I think the hole situation sucks,I will try and gap the plugs and see what happens,Alex have you see factory plugs fix pining in a supercharged truck? or did you use an aftermarket plug with a different heat rang? sorry if I did not fully explain my problem

I have to re gap spark plugs "as per roush" on a 2006 f-150 supercharged truck,has anyone done this without the use of a gapping tool? or is it best to get this tool?

I have replaced 3 of them for puffing black smoke,I did that tsb for crap in the tail pipe and could not find anything on all 3 of them,just replaced the filter and they are fix so far

I don't know why but my pcm showed up today,that was to fast to be from the USA but anyhow,installed and road tested 20 km,pcm fixed it thanks for all the input

ya I used the wrong pinpoint test,went thru it again and there about the same but only till you get to the pcm conectors,everything passes,load tested the oss circuits,because we are so busy(out of work by 10:00 am) I took off the rear tail off and inspected the trigger wheel,it looks good,I have a pcm on order but it is b/o usa with no stock so it will be at leat a week till I see it,thank for the info!

sorry its a diesel